Shut down DOSBox and make a backup of the image so you don't have to reinstall again. When setup is done it will go straight to the Windows desktop and you are done installing!.Ģ1. Start DOSBox and run the command "boot -l c" again to resume setup.Ģ2. When setup is done copying Windows files it will close DOSBox. Go to the directory on the image where you copied Windows and type in "setup /is" to install Windows.Ģ0. Execute DosBox and type in "Boot -l c" to boot your HD image.ġ9. (or you could mount the image with DOSBox and copy the files over but DOSBox may become unresponsive so you may think it ing a program like Winimage you will see a progress bar or similar so you know that it's actually working)ġ8. Open "test.img" with Winimage and copy the 9x folder you copied to your hard drive to the image. REM the below line in the section in nf since it is no longer necessary:ġ7. Run "format c: /s" to format the HD and to make it bootable.ġ6. Type in "Boot -l a" to boot your floppy image.ġ2. (Either bad images or you still have it open in another program)ġ1. If it didn't then you have done something wrong. Execute DOSBox and verify that it mounted the images correctly. (This will automatically mount the image whenever you launch DosBox)ġ0. Imgmount 2 test.img -t hdd -fs none -size 512,63,xx,xxxx Open nf and make sure that the section looks like this: (use the values from "test.bat" for -size) Put it in a directory with a short name like "9xinst".ĩ. Copy the Windows 9x CD to a folder in the DosBox directory. Copy the floppy image to the DOSBox directory.Ĩ. Name the floppy image something small like "dos622.ima".Ĩ. If you don't already have an image then use Winimage to create one or you can download an image from the internet. I'm not sure that it matters which version, as long as it's MSDOS 5.00+ then you should be good to go. Next you will next need a floppy image of MS-DOS. Move "test.img" and "test.bat" to the DOSBox 0.74 directory (if you are not going to use HAL9000's DOSBox Build to run the OS)Ħ. (Use NTFS compression on it or compress it with a compression program to save space if needed).ĥ. Make a backup copy of the image so you don't have to bother recreating it again if you wish. This command will create "test.img" in the same directory as HAL9000 MegaBuild that is 2gb in size.Ĥ. (Refer to the documentation for other options for imgmake) Create a Hard Drive image by typing "Imgmake test.img -t hd_2gig -nofs -bat" inside of DOSBox. Download HAL9000 MegaBuild v6 and install: ģ. Download and install DOSBox 0.74 (Overwrite DOSBox 0.74 files with SVN if you want to use the SVN)Ģ. Shut down DOSBox and make a backup of the image so you don't have to reinstall again.ġ. When setup is done it will go straight to the Windows desktop and you are done installing!.ġ0. Start DOSBox again and run "boot -l c".ĩ. When setup is done with the first part of setup it will close DOSBox. Go to the 9xinst directory on the image and type in "setup /NM /IS" to start the install.ħ. Execute DOSBox and boot the image with the command "boot -l c"Ħ. Copy the 9x installation files to the "9xinst" directory.ĥ. Open the 2GBfreedos.img with Winimage or IMDISK. Unzip the contents to the DOSBox directory.ģ. Download 2GBFreeDOS.zip attached to this post. *WITH WINDOWS 95B+ YOU WILL EXPERIENCE DIALOG ERRORS DURING INSTALL. GENERIC WINDOWS 9x INSTALLATION INSTRUCTIONS WinPcap (for builds of DOSBox with NE2000 support) Gulikoza or Yhkwong DOSBox build (for Glide support) Latest DOSBox version (DOSBox 0.74 as of this guide) or DOSBox SVN (7-23-2011 as of this guide) ONLY USE CPUTYPE=PENTIUM_SLOW in DOSBOX.CONF. **WINDOWS 9X WILL FREEZE OR CRASH OCCASIONALLY. INSTALL THE ATTACHED DRIVERS FOR S3 CARD. *STABILITY OF WINDOWS 9x GUEST IN DOSBOX IS HIGHLY DEPENDENT ON VIDEO DRIVERS. Windows 9x is NOT officially supported under DOSBox.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |